Relative Humidity Sample Clauses

Relative Humidity. Relative humidity was measured using an aspirated Climatronics 102425 lithium chloride sensor. The manufacturer-reported accuracy is less than ±3% RH in the range 10-90% RH. A DRI site audit in October 2002 included collocation of a continuously measuring Vaisala HMP35C sensor. Figure 5-1d shows the collocated hourly data. A reduced major axis regression yielded: Audit = (0.98 ± 0.02)× Site + (0.8 ±1.1 %RH ) The regression slope is statistically indistinguishable from unity and the intercept is statistically indistinguishable from zero (95% CL). Collocated precision was 1.1% RH (1.8% relative precision) for the 63 hours of collocated data, meeting the manufacturer-reported accuracy of less than ±3% RH. Wind Speed Wind speed was measured using a Climatronics 102083-G0-H0 (Wind Mark III series) anemometer at 10m. The manufacturer-reported accuracy is ±0.11 m/s or 1.5% with starting threshold less than 0.45 m/s. A DRI site audit in October 2002 included an evaluation of the sensor’s starting threshold using a torque wheel at a torque of 0.3 g/cm. The sensor shaft was turned at five constant speeds (0-1000 RPM) and the site sensor speed was regressed on the torque wheel speed using an ordinary linear least squares regression yielding (R2 = 1.000): Site = (0.99)× Audit + (0.09 mph) An additional check was performed by comparing the hourly-average wind speeds between the Supersite in East St. Louis and an IEPA site in Edwardsville, IL (both measurements at 10m). Data was screened to focus on advective conditions with 1,418 hours at Edwardsville exceeding 4 m/s for the period 5/8/2001-6/30/2002. A reduced major axis regression yielded (R2 = 0.693): WSEdwardsville = (1.00 ± 0.03)×WSSupersite + (0.1± 0.1 m / s) For advective conditions, there is excellent agreement between the 10m wind speeds measured at these two sites separated by ~30 km.
Sample 1
AutoNDA by SimpleDocs
Relative Humidity. Relative humidity shall be maintained at 40-60% where practical.
Sample 1
Relative Humidity a. Test Method: Perform relative humidity test using in situ probes according to ASTM F 2170. b. Acceptable Results: Not more than 75 percent.
Sample 1
Relative Humidity. A value of 100% relative humidity was used, and was only applicable for the emission modeling. It is important to note that for temperatures of 75 degrees Fahrenheit and below relative humidity has no effect on CO emission rates. Table 4.1 - MOVES input parameters by scenario Parameter Freeway Arterial Intersection Scale Project Level Domain Project Level Domain Project Level Domain Year 0000 0000 0000 Month January January January Time Span - Hour 12:00 AM 12:00 AM 12:00 AM Time Span - Day Weekday Weekday Weekday Geographic Bounds Custom Domain Custom Domain Custom Domain Temperature -10° Fahrenheit -10° Fahrenheit -10° Fahrenheit Relative Humidity 100% 100% 100% Fuel Formulation Gasoline – Formulation ID - 3812 Gasoline – Formulation ID - 3812 Gasoline – Formulation ID - 3812 Diesel – Formulation ID - 20011 Diesel – Formulation ID - 20011 Diesel – Formulation ID - 20011 CNG – Formulation ID - 30 CNG – Formulation ID - 30 CNG – Formulation ID - 30 Fleet Mix Emission Source Type and Fuel Combinations for 2015 with a Shift to 0% Heavy-Duty Truck Volumes to Reflect Higher CO emission Rates from Gasoline Vehicles (refer to through Table 4.4 - Table C-6)) Emission Source Type and Fuel Combinations for 2015 with a Shift to 0% Heavy-Duty Truck Volumes to Reflect Higher CO emission Rates from Gasoline Vehicles (refer to Table 4.4 - Table C-6) Emission Source Type and Fuel Combinations for 2015 with a Shift to 0% Heavy-Duty Truck Volumes to Reflect Higher CO emission Rates from Gasoline Vehicles (refer to Table 4.4 - Table C-6)) Age Distribution 2015 National Default 2015 National Default 2015 National Default Link Source Type Distribution Variable - Based on 2015 National Default VMT for Urban Restricted Access Road Type Variable - Based on 2015 National Default VMT for Urban Unrestricted Access Road Type Variable - Based on 2015 National Default VMT for Urban Unrestricted Access Road Type Road Type Urban and Rural Restricted Access Urban and Rural Unrestricted Access Urban and Rural Unrestricted Access Link Average Speed 74 mph 45 mph 15, 25 and 35 mph approach and idle (intersection) Grade ±7% , ±4%, ± 2%, ± 0% (uphill and downhill grade) ±4%, ± 2%, ± 0% (uphill and downhill grade) ± 2% (cross direction) and 0% grade in other direction (intersection) Inspection & Maintenance None None None
Sample 1
Relative Humidity. A value of 100% relative humidity was used and was only applicable for the emission modeling, which yields the highest CO emission rates for any temperature over 75 degrees Fahrenheit.
Sample 1
Relative Humidity. LESSOR warrants that the Leased Premises are served by heating, cooling and other facilities of a design capacity sufficient to maintain the Leased Premises at a humidity level within the range of 20% - 60% relative humidity, assuming optimal use of the thermostats and other climate control devices, such as the opening or closing of blinds, doors and vents, within the Leased Premises.
Sample 1

Related to Relative Humidity

  • Reallocation to a Class with a Lower Salary Range Maximum 1. If the employee meets the skills and abilities requirements of the position and chooses to remain in the reallocated position, the employee retains existing appointment status and has the right to be placed on the Employer’s internal layoff list for the classification occupied prior to the reallocation.

  • CLASS SIZE/STAFFING LEVELS The board will make every effort to limit FDK/Grade 1 split grades where feasible. APPENDIX A – RETIREMENT GRATUITIES

  • OPWC/Local Subdivision Participation Percentages For the sole and express purpose of financing/reimbursing costs of the Project, the estimated costs of which are set forth and described below, the Recipient hereby designates its Local Subdivision Percentage Contribution as amounting to a minimum total value of 50% of the total Project Cost. The OPWC Participation Percentage shall be 50% not to exceed $100,000.

  • Reallocation to a Class with a Higher Salary Range Maximum Upon appointment to the higher class, the employee’s base salary will be increased to a step of the range for the new class that is nearest to five percent (5.0%) higher than the amount of the pre-promotional step, or to the entry step of the new range, whichever is higher.

  • Horizontal Movement The Board encourages all unit members to improve their skills through advanced training and, as an inducement thereto, provides extra compensation for those who do so successfully. The Board delegates to the Superintendent the responsibility for assuring that unit members comply with the following regulations when claiming credit for advanced studies.

  • COSTS DISTRIBUTED THROUGH COUNTYWIDE COST ALLOCATIONS The indirect overhead and support service costs listed in the Summary Schedule (attached) are formally approved as actual costs for fiscal year 2020-21, and as estimated costs for fiscal year 2022-23 on a “fixed with carry-forward” basis. These costs may be included as part of the county departments’ costs indicated effective July 1, 2022, for further allocation to federal grants and contracts performed by the respective county departments.

  • Basement Any leaks or evidence of moisture? Yes No Unknown Does Not Apply Comments:

  • Line Splitting – UNE-L In the event TWTC provides its own switching or obtains switching from a third party, TWTC may engage in line splitting arrangements with another CLEC using a splitter, provided by TWTC, in a Version: 4Q06 Standard ICA 11/30/06 Collocation Space at the central office where the loop terminates into a distribution frame or its equivalent.

  • Reallocation to a Class with an Equal Salary Range Maximum 1. If the employee meets the skills and abilities requirements of the position, the employee remains in the position and retains existing appointment status.

  • Clearcutting Units All trees that meet Utilization Standards within “Clearcutting Units” are designated for cutting.

Time is Money Join Law Insider Premium to draft better contracts faster.