Tensile properties Sample Clauses

Tensile properties. The mechanical properties of the steel in the finished cylinder or liner shall be determined in accordance with paragraph A.1 (Appendix A). The elongation for steel shall be at least 14 per cent;
Sample 1Sample 2Sample 3See All (31)
AutoNDA by SimpleDocs
Tensile properties. The mechanical properties of the aluminium alloy in the finished cylinder shall be determined in accordance with paragraph A.l (Appendix A). The elongation for aluminium shall be at least 12 per cent.
Sample 1Sample 2Sample 3See All (31)
Tensile properties. The tensile strength should be measured for pressure pipe applications in accordance with Test Method D638 and must meet the requirements of Section 4.3.
Sample 1
Tensile properties. The tensile tests were performed in both ferritic (F) as well as tempered martensitic (TM) state. Fig. 5 shows the comparison of yield strength (Rp0.2) and ultimate tensile strength (Rm) of 9YWT-MATISSE in both ferritic and tempered martensitic states at various testing temperatures. In both states, the steel displayed similar trends of strength as the temperature increases. The improvement of strength at room temperature for the TM state is evident from Fig. 5. The engineering stress-strain curves (Fig. 6) show a significant strain hardening for both states at room temperature. Interestingly, the F state exhibited a yield point phenomenon at room temperature. On the contrary, the results obtained at elevated temperatures were quite different. The prominent improvement in strength for the TM state was gradually lost as both states appeared to approach a common low-strength value as the temperature increases. The strain hardening became much less significant at these temperatures. The main tensile properties for the TM state are summarized in Table 2. At room temperature, the TM state exhibited high yield strength and ultimate tensile strength of 929 and 1052 MPa, respectively. A decrease in strength was observed when the temperature increases. This decrease seemed to be more pronounced above 500°C with 156 MPa of ultimate tensile strength at 800°C. Similar statements can be made for the steel in the F state. The main tensile properties for the F state are summarized in Table 3. Fig. 5: Comparison of yield strength (Rp0.2) and tensile strength (Rm) of 9YWT-MATISSE in ferritic (F) and tempered martensitic (TM) states at various testing temperatures.
Sample 1

Related to Tensile properties

  • Title to Properties The Company and each Subsidiary have good record and marketable title in fee simple to, or valid leasehold interests in, all real property necessary or used in the ordinary conduct of their respective businesses, except for such defects in title as could not, individually or in the aggregate, have a Material Adverse Effect. As of the Closing Date, the property of the Company and its Subsidiaries is subject to no Liens, other than Permitted Liens.

  • Access to Property, Property’s Management, Property Lender, and Property Tenants Potential Investor agrees to not seek to gain access to any non-public areas of the Property or communicate with Property’s management employees, the holder of any financing encumbering the Property, the Property’s tenants, and the Owner’s partners in the ownership of the Property, without the prior consent of Owner or HFF, which consent may be withheld in the Owner’s sole discretion.

  • Properties and Leases Except as would not, individually or in the aggregate, reasonably be expected to have a Company Material Adverse Effect, the Company and the Company Subsidiaries have good and marketable title to all real properties and all other properties and assets owned by them, in each case free from liens, encumbrances, claims and defects that would affect the value thereof or interfere with the use made or to be made thereof by them. Except as would not, individually or in the aggregate, reasonably be expected to have a Company Material Adverse Effect, the Company and the Company Subsidiaries hold all leased real or personal property under valid and enforceable leases with no exceptions that would interfere with the use made or to be made thereof by them.

  • Property Ownership The Fund owns or leases all such properties as are necessary to the conduct of its operations as presently conducted.

  • INCOME FROM IMMOVABLE PROPERTY 1. Income derived by a resident of a Contracting State from immovable property (including income from agriculture or forestry) situated in the other Contracting State may be taxed in that other State.

  • Real Property (a) The Company does not own any real property.

Time is Money Join Law Insider Premium to draft better contracts faster.